Skip to content
Glossary

Plumber Glossary

Plain definitions of 34 terms we use on the job in Maple Valley.

Term Index

Browse Individual Glossary Pages

Open any term below for a dedicated definition page.

ABS Pipe

ABS Pipe is a black plastic drain pipe made from acrylonitrile butadiene styrene. It carries wastewater from fixtures through a building’s drainage system and toward a sewer connection. ABS pipe joins with solvent cement, which bonds fittings and pipe into sealed sections. Plumbers commonly use it for underground sewer and drain lines.

Also called: Acrylonitrile Butadiene Styrene Pipe

Read full definition

Air Gap

An air gap is a physical break between a dishwasher drain hose and the drain connection. The break uses open space to stop dirty sink or disposal water from flowing back into the dishwasher. A countertop air gap fitting usually connects to the sink drain or garbage disposal beneath the sink.

Read full definition

Anode Rod

Anode Rod is a sacrificial metal rod installed inside a tank water heater. The rod attracts corrosive elements in the stored water, which helps protect the steel tank from rust. As the rod wears down, the tank loses that protection. A plumber checks its condition during water heater repair or maintenance.

Also called: Sacrificial Anode

Read full definition

Backwater Valve

A backwater valve is a sewer pipe fitting that helps stop wastewater from flowing backward into a building. A hinged flap or similar gate allows drainage to leave the building, then closes when flow reverses. The valve is usually placed in an accessible section of the building sewer line for service and inspection.

Also called: Backflow Valve

Read full definition

Ball Valve

A ball valve is a shutoff device that controls water flow with a round, drilled ball inside its body. Turning the handle rotates the ball so its opening lines up with the pipe or blocks the passage. Ball valves provide quick, full flow control on water supply lines and equipment connections.

Read full definition

Cleanout

A cleanout is an access point in a drain or sewer pipe. A removable cap covers the opening and keeps normal wastewater contained. Plumbers remove the cap to inspect the line, clear blockages, or flush buildup. Cleanouts may be found indoors, outdoors, or near a building’s connection to the public sewer.

Also called: Drain Cleanout

Read full definition

Compression Fitting

A Compression Fitting is a plumbing connector that joins tubing without soldering, welding, or adhesive. A threaded body, nut, and compression ring create the seal. Tightening the nut presses the ring against the tube. This design supports repairs on accessible water lines and allows the connection to be taken apart when needed.

Read full definition

Cross-Connection

A cross-connection is a physical link between a drinking water supply and another source that could affect water quality. The link may be intentional, such as a hose connection, or created by equipment, such as a boiler or irrigation system. Backflow through that link can move unwanted water into the supply.

Read full definition

Dielectric Union

A Dielectric Union is a plumbing fitting that joins two different metals while limiting electrical contact between them. The fitting uses an insulating washer and sleeve to separate the metal parts. This separation helps reduce galvanic corrosion, which can weaken connections where copper and steel piping meet on a water heater.

Read full definition

Drain Auger

A drain auger is a plumbing tool with a flexible cable that rotates through a clogged drain. The cable breaks apart or catches material blocking the pipe. Drain augers work on sinks, tubs, showers, toilets, and some larger drain lines. The tool can clear a blockage without removing the entire pipe.

Also called: Drain Snake

Read full definition

Drain Trap

A drain trap is a curved section of drainpipe that holds water and blocks sewer gases from entering a building. The trap sits below fixtures such as sinks, showers, tubs, and toilets. Its shape also catches some debris, which can contribute to slow drainage or clogs that need cleaning.

Also called: P-Trap

Read full definition

Expansion Tank

An Expansion Tank is a small water heater component that absorbs pressure from heated water as the water expands. It connects to the cold-water line near the heater and uses an air cushion to hold the extra volume. The tank helps limit pressure changes that can strain pipes, fittings, and heater parts.

Also called: Thermal Expansion Tank

Read full definition

Flapper Valve

A flapper valve is a rubber or plastic seal inside a toilet tank. The valve covers the flush valve opening and holds water in the tank until you press the handle. When the handle lifts the flapper, tank water enters the bowl and starts the flush. Afterward, the flapper closes again.

Also called: Toilet Flapper

Read full definition

Float Switch

A float switch is a water-level sensor that turns a sump pump on or off as water rises or falls. The switch uses a floating part connected to an electrical control. When the water reaches the set level, the switch signals the pump to run and helps protect the sump pit from overflow.

Read full definition

Gate Valve

Gate Valve is a shutoff device that controls water flow with a flat or wedge-shaped gate. Turning the handwheel raises or lowers the gate inside the valve body. A gate valve allows water to pass through a mostly open channel when open. It is designed for full open or full closed service, not flow adjustment.

Read full definition

Heating Element

A Heating Element is an electric water heater part that turns electrical energy into heat. The element sits inside the tank and warms the water around it. A thermostat controls when the element turns on and off. If the element fails, the water heater may produce lukewarm water or no hot water.

Read full definition

Main Shutoff Valve

Main Shutoff Valve is the control that stops water from entering a building through the main supply line. The valve sits near the water meter or where the service line enters the building. Closing it cuts water flow to plumbing fixtures, appliances, and branch pipes throughout the property.

Also called: Main Water Shutoff

Read full definition

Pipe Bursting

Pipe Bursting is a trenchless sewer repair method that breaks an old underground pipe while pulling a new pipe through the same path. The replacement pipe takes the old pipe’s place with little surface digging. This method can address severe cracks, collapses, or other failures when the existing route remains usable.

Also called: Static Pipe Bursting

Read full definition

Pipe Dope

Pipe Dope is a paste-like thread sealant used on threaded pipe connections. The compound fills small gaps between matching threads, helping prevent water from escaping through the joint. Plumbers choose a formula that suits the pipe material and the fluid carried through the line. Pipe dope is not pipe glue.

Also called: Thread Sealant

Read full definition

Pressure Reducing Valve

Pressure Reducing Valve is a plumbing control that lowers incoming water pressure to a safer, steadier level for a building’s pipes and fixtures. The valve uses a spring and diaphragm to sense pressure and adjust the water opening. It helps prevent pressure-related leaks, noise, and damage inside a home.

Also called: PRV

Read full definition

Sewer Cleanout

A sewer cleanout is an access point on a building’s drain line or sewer lateral. The opening has a removable cap and gives plumbers a direct path into the pipe. Plumbers use it to clear blockages, inspect flow, and reach the line without removing indoor fixtures or digging up the entire route.

Read full definition

Sewer Lateral

A sewer lateral is the buried pipe that carries wastewater from a building's drain system to a public sewer main or private treatment system. The lateral may cross private property, public right of way, or both. Its condition affects how wastewater leaves the property and connects with the larger sewer network.

Also called: Lateral Sewer Line

Read full definition

Sewer Pipe Belly

A Sewer Pipe Belly is a low section in a sewer pipe where soil movement, settling, or poor installation has changed the pipe’s slope. Wastewater and sediment can collect in that low spot. The condition may restrict flow and contribute to repeated backups, slow drainage, or difficult sewer cleaning.

Also called: Sewer Line Belly

Read full definition

Sump Pump Float Switch

A Sump Pump Float Switch is a control that turns a sump pump on as water rises and off as water falls. The switch floats on the water or moves with a tether. Its position signals the pump motor, helping remove water from a sump pit without constant manual operation.

Also called: Sump Float Switch

Read full definition

Toilet Flange

A toilet flange is a floor-mounted fitting that connects a toilet’s outlet to the drainpipe and anchors the toilet in place. The flange sits around the drain opening and supports the toilet bolts. A sealing ring between the toilet and flange helps prevent wastewater and sewer gases from escaping.

Also called: Closet Flange

Read full definition

TPR Valve

A TPR valve is a water heater safety component that opens when tank temperature or pressure rises too high. The valve releases hot water and pressure through a discharge pipe. This action helps protect the tank from dangerous stress. TPR valves are commonly found on storage-tank water heaters and must remain connected and unobstructed.

Also called: Temperature and Pressure Relief Valve

Read full definition

Trap Primer

A trap primer is a plumbing device that adds water to a drain trap when the trap could dry out. The added water helps maintain the trap seal, which blocks sewer gases from entering a building. Trap primers often serve floor drains in spaces that receive little regular drainage.

Read full definition

Vacuum Breaker

A Vacuum Breaker is a backflow prevention device that stops siphoning when water pressure drops. The device admits air into a water line, which breaks the vacuum that could pull contaminated water backward. Vacuum breakers commonly protect hose connections, irrigation lines, and other outlets where a cross-connection may occur.

Also called: Anti-Siphon Valve

Read full definition

Water Hammer

Water Hammer is a pressure surge in a plumbing system caused by moving water that stops or changes direction suddenly. The surge can make pipes bang, vibrate, or shake near valves and fixtures. Water hammer often appears when a faucet, toilet valve, washing machine valve, or other control closes quickly.

Also called: Hydraulic Shock

Read full definition

Water Heater Sediment

Water Heater Sediment is loose material that settles inside a water heater tank. The material often includes minerals from the water supply and can collect near the bottom of the tank. Sediment may form a layer that affects heating, causes rumbling sounds, or reduces available hot water when buildup becomes heavy.

Also called: Tank Sediment

Read full definition

Water Heater Thermostat

A Water Heater Thermostat is a temperature control that senses water heat and signals the heating system to turn on or off. Electric water heaters often use thermostats with heating elements, while gas models may use a thermostat built into the gas control valve. The setting guides the tank’s operating temperature.

Also called: Thermostat

Read full definition

Water Meter

A Water Meter is a device that measures the volume of water entering a property through its supply line. The meter records water use for billing and helps identify changes in flow. It usually sits near the property connection, often in an underground box, and connects the public water system to private plumbing.

Read full definition

Water Shutoff Valve

A water shutoff valve is a plumbing control that stops water flow through a supply pipe. You can close the valve to isolate a fixture, appliance, branch line, or the whole building. This control helps limit water damage during a leak and allows plumbing work on connected parts.

Also called: Water Stop Valve

Read full definition

Weep Hole

A Weep Hole is a small opening drilled in a sump pump discharge pipe near the pump. The opening lets trapped air escape, which helps prevent an air lock that could stop water from leaving the sump basin. It also allows a small amount of water to return to the basin.

Also called: Drainage Hole

Read full definition

(425) 475-3519